10″ Benchtop Jointer
$649.99
SPECIAL !
Buy an 8” or 10” jointer and Get a Fence Stabilizer System ($19.99 Value) for FREE!
Free shipping on all machines To lower 48 states
- No More Cupped Woods. Create perfectly flat surfaces and edges quickly and hassle-free with the Wahuda Jointers. Experience smoother and accurate cuts even on tough or figured woods w/ Wahuda Tools.
- Cutting-Edge Sharpness. Our spiral cutterhead has 4-sided carbide inserts for sharper and quieter cutting precision. The standard blade size also allows for a cost-effective and simple replacement.
- Capable Steady Performance. Wahuda Jointers are powered with a 120V motor with a fixed 12,000 RPM. They are fully capable of handling edging, jointing, flattening, or tapering no matter the surface!
- Solid Built For Your Convenience. Our adjustable and expandable cast iron tables enhance stability even when working on longer, larger pieces, with a fence that tilts from 90 &135° for versatility.
- Perfect For Job Sites Or Small Shops. Depending on your needs or your shop’s size, Wahuda Tools have 6, 8, and 10-inch wood jointers that will do the job right. They’re conveniently movable, too!
Features & Specs
10-Inch Woodworking Jointer
If our 6" or 8" bench top jointers do not quite have the width capacity you are looking for, we'd like to introduce our new 10" WAHUDA spiral style bench top jointer model 50110CC-WHD.
As with our other jointers, our new 10" model is very capable of milling stock in a small pro shop. It's also manufactured to tight tolerances in a certified ISO 9001 factory and is CSA approved for performance and your safety.
With the cast iron tables, our newest jointer weighs about 74 lbs, making it easily maneuvered around your shop or jobsite. The cast iron tables also provide better stability during operation and are less prone to scratching. Table leveling for coplanar, if ever needed, is easily achieved via set screws installed in each table. Even the pull out extensions are easily adjustable for coplanar if necessary. With the 33 1/2" total table length end to end, extendable to 51" of usable support with the table extensions pulled out, machine depth of around 22", and total height of about 13 3/8", it will fit in just about the same footprint as the 8" jointer.
The newly incorporated spiral style cutterhead, manufactured with the same heavy duty aluminum extrusion over steel inner shaft, now provides you the cutting edge sharpness retention from having 20 carbide 4-sided insert tips installed. While being quieter than the straight knife cutterhead noise you have had to endure, you also get the smooth finish on your stock you've been looking for from the spiral design ... even on figured woods. And only having to loosen or remove one mounting screw on each insert, provides extremely quick tip rotation or replacement if the insert becomes nicked. This keeps your downtime to a minimum and your project on time.
Our new 10" jointer has some of the same features as our previous highly rated models. It has a maximum capacity of 10" face planing width and 1/8" maximum depth of cut and a 4" included dust port with 2 1/2" adapter for better chip evacuation. This model has a 4 3/8" high by 24" long extruded aluminum fence which can be easily tilted from 90 to 135 degrees with ease. It has a 120V 12 amp AC motor which provides ample machining power. Included are the push blocks, the tools you need to properly set up and adjust the machine, and a T-Torx wrench to rotate or replace the insert tips.
If you feel our new 10" jointer is a bit of overkill for your needs, or a little too large of footprint for your available shop space, check out our 6" and 8" bench top jointers.
Features
- Powerful 12 Amp 120V motor
Newly Incorporated Spiral Style Cutterhead with 20 4-sided carbide Inserts
Long Extruded Fence with 90 to 135 Degree Tilt
Adjustable and expandable table extensionsIf you're looking for a little bit more length or width capacity than our 6" or 8" jointers have, take a look at this 10" jointer. This compact benchtop jointer packs a lot of punch. And as small power jointers go, it's at the top of its class. It has a 33 1/2" table length, end-to-end, with table extensions allowing it to increase in length to 53 1/2". It's about 22” deep, 13 3/8” high, and weighs about 74 lbs, making it easy to move around in the shop or out on the job site.The new spiral cutterhead features 20 4-sided carbide-tipped inserts that can quickly and easily be rotated to a new edge if an old one gets chipped or otherwise damaged. The 120V 12 amp motor provides all the power you'll need.
Warranty
2 YEAR LIMITED WARRANTY
WAHUDA warrants its machinery to be free of defects in workmanship and materials for a period of two (2) years from the date of the original purchase by the original owner. This warranty applies to products sold in United States only. The warranty does not apply to any product used for professional or commercial production purposes nor for industrial or educational applications. Such cases are covered by our 1 year Limited Warranty with the Conditions and Exceptions.Product Size
Speed
12,000 RPM
Inserts
Max Depth of Cut
Max Cutting Width
Max Stock Thickness
Feed Rate
20 Four-sided Inserts carbide
1/8"
10"
--
--
Tables
Fence Size
Dust Port
Weight
Base
WARRANTY
10" x 33 1/2" Extendable to 53.5"
4 3/8" X 24"
2 1/2" and 4"
73.4 lbs.
19" X 13 1/2"
2 YEARS
Video
17 reviews for 10" Benchtop Jointer
You must be logged in to post a review.
ALLEN –
Product is fantastic. Have not had a chance to use it a lot, but set up and initial use were great. Only issue I had was that the product was packed upside down in the box. The labels on the outside of the box were opposite of the way it was packed. Not a big deal but had to flip it over to get the product out of the box. Other than that great product, great company to deal with. Ordering was easy, shipping was fast and reliable. Looking forward to using the joiner on a lot of projects I have coming up.
zac –
So far so good. Wish the table was rust proof. But oh well..
Ed Dixon –
I love my 8″ Wahuda jointer, however the 10″ wasn’t an option when I bought it. Do you offer a trade-in program? 😀
ChiaoLing Huang –
Hello Ed,
We hope that you were happy with the 8 and currently we don’t have any trade-in program.
Team Wahuda
Jon Vios –
Excellent, customer service!
vince –
I chose Wahuda because it’s one of the few benchtop jointers available in a 10″ model, and so far I’m very happy with it. From order to delivery was just a few days, and although I envisioned the setup to take a lot of time, it went from out of the box to dialed-in and running in less than an hour. Assembly itself was easy…getting the fence squared was the only part I found myself taking a lot of time with. In my case, both the infeed and outfeed tables were perfect from the factory, so that part was easy. It seems to have ample power for everything I’ve fed through it, including maple, walnut and ebony hardwoods. The dust collection works fairly well, and about the only issue I’ve noticed is that it seems to be more sensitive to knots than other jointers I’ve used. Given that it saves me thousands of dollars and a lot of floor space over what a 10″ floor-standing jointer would require, I feel this was the best choice for my needs.
Richard –
I purchased the 10″ jointer at the end of October in 2022 to replace my several years old 6″ floor jointer. It took a couple of hours to set it up so the infeed, outfeed tables and the extensions were parallel and flat. I think the table adjustment process is cumbersome using the 4 sets of dual set screws and the locking screw on each table. Fortunately I have two precision straight edges so it wasn’t difficult just a PITA. I also decided that the plastic fence locking ratchet levers were inadequate, so I replaced both of them with metal M08x60 ones that I purchased on the Zoro website. The fence is now rock solid with no flex and I don’t have to worry about the plastic levers breaking off. The jointer works like a dream and is quieter than expected. I planed several boards and they are all smooth and shiny as well as exceptionally flat. There was no tear-out even around knots and reversing grain directions. I would definitely recommend this jointer.
Sam Sullivan –
Superb jointer. Does require some fine tuning out of the box after assembly; I was lucky enough to have my outfeed table pretty much good to go out of the box, but did need to adjust the infeed table and extensions to get everything flat and parallel. Between that and squaring up the fence, overall time to get the whole thing dialed in was about 90 minutes or so. But once you have it all tuned up, it’s FANTASTIC. The cutterhead’s carbide inserts provide a glass smooth finish on everything I run through it, including hardwooods, and the 10in table is a real luxury.
This thing competes with floor jointers at a fraction of the cost and shop footprint. Definitely recommend this for hobbyists, or anybody with a smaller shop. For this price, you really can’t go wrong.
npappada55 –
Awesome. I cannot say enough great things about the 10” Bench Top Jointer 50110CC-WHD. With the carbide inserts the cutter produces a super smooth finish on my project wood. This machine has plenty of power and the Engineering and precision build is evident when you operate it. I purchased the Universal Stand 80300US-WHD and it’s an outstanding build that fits this jointer perfectly. I really think the set screw fence stop adjustments for 90 and 135 degrees isn’t solid enough to count on. I will use my own precision gages when I make these adjustments. Thanks Wahuda Tools for the excellent products.
Michael Louden –
This thing is a beast! I’ve put through 9 inch wide boards of maple, walnut, and cherry with no problems. Took me a few hours to get it set up and level but haven’t had any issues so far. Definitely well worth the price.
James Sanders –
Great deal
I hadn’t ever seen a jointer over 6†that was 110v. I build furniture for a living and have a larger 5hp jointer at my shop. I bought this one for home use. I wouldn’t use it to joint 8’ long boards but for home projects it is great. The fence is trash but you can build a plywood one pretty easily. There are adjustments for the bed angles but mine came in already coplaned. I’ve only ran walnut through it but some of the pieces were 9†wide and it went fine. It’s not professional grade but it’s well worth the price.
July 25, 2021
Eric F –
What a beast!
I upgraded from an older 6 inch Cutech (still worked great after many board feet) to the Wahuda 10 inch with cast iron tables and outrigger extensions.
I’m very pleased with this machine.
Tuning the tables was easy thanks to the video guide. A full size 4 inch dust port is great with a dust right quick connect.
The machine leaves a glass surface and chows through 6 inch hard maple like it was nothing. Of course feed rate and a reasonable depth of cut are keys to success.
I’m really excited about all of the capacity on this jointer. 10 inch!! In a bench top!! I doubt I will be using my planer sled very much, if at all.
I do wish the fence were cast instead of aluminum but the set screws seem to be more reliable with this model.
The outriggers are a huge upgrade feature. Next best thing to longer tables and again they were easy to adjust to be on the same plane as the tables thanks to that video.
4 sided cutters is another nice upgrade.
My material comes of the machine dead flat and ready for my planer, also purchased from this company.
Great machine for a great value
June 23, 2021
Robert Young –
Amazing value!
Ordered Sunday evening, received Tuesday afternoon via free shipping. Cast iron beds were precisely flat & coplanar. Fence assembly hardware is imprecise, can leave it slightly tilted up/down or forward/rearward, but it is easily set to perpendicular which is what matters. Extensions could easily be set coplanar with beds, but not at both extended and retracted positions. (BTW, stuck extension rods can be cured simply by rotating them when the adjustment screws are loosened.) Removable carbide cutters leave a slick, smooth surface. To get this superb 10″ jointer with rotatable, replaceable carbide cutters for just $700 is truly incredible. Thank you, Wahuda!
March 9, 2021
Spencer A. –
Excellent Machine
I use this to mill rough sawn hardwood (cherry, maple, etc) logs into boards. It works like a champ. Took about 2 hours to get it set up, but after that, I’ve had nothing but phenomenal results. I made a video review on YouTube on the Block2Boxes channel if you’re interested in seeing the unboxing and full review of it. Great product, Wahuda!
February 19, 2021
Don M –
Everything and More
I bought the 10 inch to face off 9 to 10 inch wide 24 inch long rough split quartersawn billets of Englemann Spruce. Wahuda tech said there would be no problem – and they were right . The 12 amp motor is more than adequate to handle my billets.
I also ran thru some 50 year old highly figured Big Leaf Maple chain sawn billets and this machine handled them easily – Very smooth cut on the figured Maple.
January 17, 2021
William T –
Great Tool
I ordered the 10″ Jointer when they first became available. It took about 3 hours to set the tables up properly (I’m picky) I had two very minor issues that customer service fixed right away. The tool works to my expectation. for the price I haven’t seen anything better.
December 29, 2020
Joah –
Perfect for what I need
I had been considering the 8” version for a while. The time was finally right to make a purchase and I was pleasantly surprised to learn about the 10” option. I mainly make cutting boards and smaller decorations that do not require pieces over 4-5 feet usually – so this jointer works great for my needs. Setup took me a few hours. I used a 24” precision straight edge (0.001 precision) and feeer gauges. There is a 0.004 low spot on the outfeed table against edge nearest the fence. It’s a few inches from the cutter head so I don’t think it will be any issue. I did have to adjust both of the extension arms. Both were too low. I spent today running a bunch of 6” wide cherry, maple, and walnut through it. It powered through it all with no issue at all. I have a big 9” wide piece of hard maple that I’m going push through it soon. That will be the true test. All in all I’m very happy with it.
December 5, 2020
Andrew Boise –
10″ Benchtop Jointer
This is the only 10″ benchtop jointer that I know of on the market. It took a few hours to get it dialed in as it was not set up properly from the factory. Make sure you get yourself a good level and some feeler gauges. Once dialed in though it has been working great for face jointing and pieces up to about 4′ long. Exactly what I needed for table legs and coffee tabletops. Have to go a little slower than when using a true helical head, but it produces a smooth finish with the right feed speed.
November 17, 2020